600cc - 900cc - Page 12

ervins · 04-27-2006

Welcome to the forum!

jimmyh · 05-05-2006

Quote:

Originally Posted by 93NINJAZX600-R

OMg I read in the other posts that the oil level is supposed to be in the middle, well my oil isn't it is full and has been that way, WOW . I hope I don't hurt it, i am going today to get a oil change so please anyone that can tell me anything please do thanks..

I am not an expert on bikes, but I know with car engines, overfilling the oil is one of the worst things you can do. You can screw up the piston rings, the cat, and more. I always slightly underfill my car, and have been doing the same with my bike. If it starts to get low, you can always add more, it is certainly easier than trying to drain just some.

jimmyh · 05-05-2006

I posted this in another thread, but thought I should put it here also since this one is sticky.

http://www.cooleywire.com/jimmyh/pics/mirror.html

These mirrors are awesome. NO vibration. Complete view behind you. And they cost less than $60 shipped. However, they dont fold, and a little modification to the fairing bracket is required. Very simple though.

MikeKawasaki · 05-06-2006

Quote:

Originally Posted by Sacheen

Hey all!

I'm a tad disappointed in the mileage I've been getting out of my ZZR. Between 184 to 200 miles per tank. Does that seem a tad too low?

What kind of gas mileage do other 600cc riders experience?

I'm going on reserve at 185 miles. I got 60 mpg when a was just cruzin a tank out. 50 to 55 avg.

ervins · 05-06-2006

Quote:

Originally Posted by jimmyh

I posted this in another thread, but thought I should put it here also since this one is sticky.

http://www.cooleywire.com/jimmyh/pics/mirror.html

These mirrors are awesome. NO vibration. Complete view behind you. And they cost less than $60 shipped. However, they dont fold, and a little modification to the fairing bracket is required. Very simple though.

Great job Jimmy! Looks good. I wish I did not have to mod anything alter the look of my bike too much. If it weren't for that, I would do this. I just tuck my elbows in and look or turn regardless...I do see alot of elbow but I have my method that for some reason works really well. Great write up and thanks for giving everyone options. A more expensive way is to make one but then you would need someone to do the mold, etc.

r409z · 05-07-2006

I am excited...I just ordered the following:
akrapovic slip on
CA smoke integrated tail
fenderkit.com eliminator
no cut sliders
swingarm spools
tank pad
gpr steering stabilizer

ervins · 05-08-2006

Quote:

Originally Posted by r409z

I am excited...I just ordered the following:
akrapovic slip on
CA smoke integrated tail
fenderkit.com eliminator
no cut sliders
swingarm spools
tank pad
gpr steering stabilizer

Mod bug going around! Congrats on the purchase and show us updated pics when you get them on. The CA tail is awesome.

1LtRocket · 05-08-2006

Help Plz!! With the FI and tech on the 06ZX-6R of mine I had to replace the servo under the seat with the block 1 muzzy sent me. Well i wasnt paying attention when i installed and got it on 180 degrees backwards when switched the key on it moved and now the FI light stays on which this was the purpose of the part. I tried to move it back but i cant. Does anyone know if i can take the servo out and reset it then put my block back on properly. the service manual on talks about dam computer error codes any feedback would be helpfull. !!!! Thanks

kaliton636 · 05-09-2006

Quote:

Originally Posted by ervins

Mod bug going around! Congrats on the purchase and show us updated pics when you get them on. The CA tail is awesome.

I like the hotbodies undertail for the 03-04 zx6r

r409z · 05-10-2006

Quote:

Originally Posted by kaliton636

I like the hotbodies undertail for the 03-04 zx6r

I was so close to getting the hot bodies exhaust for my 06, but I have seen/heard of too many of them melting...not something I want to deal with.

05-636 · 05-11-2006

Quote:

Originally Posted by ervins

Mod bug going around! Congrats on the purchase and show us updated pics when you get them on. The CA tail is awesome.

Must be I just got my seat cowl inthe mail Today.....err...yesterday however you want to look at it. Also just ordered my PCIII. In a week or two I'll be ordering the the Muzzy for her.

ervins · 05-11-2006

Quote:

Originally Posted by 05-636

Must be I just got my seat cowl inthe mail Today.....err...yesterday however you want to look at it. Also just ordered my PCIII. In a week or two I'll be ordering the the Muzzy for her.

Yep, got my highmount red Micron exhaust today! Geez that thing will look awesome on my bike...I am going to a ceramic coater tomorrow to coat all the mounting and brackets black tomorrow. This will keep my black/ red theme and make the Micron look that much better. I can't wait!

ninja636billy · 05-11-2006

Quote:

Originally Posted by ervins

Yep, got my highmount red Micron exhaust today! Geez that thing will look awesome on my bike...I am going to a ceramic coater tomorrow to coat all the mounting and brackets black tomorrow. This will keep my black/ red theme and make the Micron look that much better. I can't wait!

nice, get some pics then.

onx · 05-11-2006

Sorry posted in wrong thread...thought I was posting in the 250/500cc thread (firefox tabs...got all confused =( )

Fortheu22 · 05-12-2006

I was looking at parts and I called a local dealership here and they said the 2001 zx-6r aftermarket parts MIGHT fit my 2006 kawi zzr anyone know if this is true?

ervins · 05-12-2006

Quote:

Originally Posted by Fortheu22

I was looking at parts and I called a local dealership here and they said the 2001 zx-6r aftermarket parts MIGHT fit my 2006 kawi zzr anyone know if this is true?

I beleive it does as that bike eventually became their sport touring bike.

05-636 · 05-14-2006

Quote:

Originally Posted by Fortheu22

I was looking at parts and I called a local dealership here and they said the 2001 zx-6r aftermarket parts MIGHT fit my 2006 kawi zzr anyone know if this is true?

they should. It's the same bike just with different badging and handlebar risers.

NinjaRdr · 05-14-2006

Hello All,

Have been posting in another thread, but since my 93' zx600c is close to road readiness, thought that I would ask a question about the front wheel mounting. I removed the wheel and took it into a shop to have a new tire (120/80/16) mounted. In the process, I am putting new brake pads on it. Since I cannot remember exactly how the hub/axle spacer goes on, can you tell me if I got it on right? I installed it with the wider (lip) next to the fork. And how tight is all of this supposed to be? How freely should the wheel spin with the new brake pads, etc, installed? Thank you.

NinjaRdr

otp · 05-14-2006

zx 600rA 1985-88
NEED CRANK SHAFT soo i can ride again.It spun the #3 piston and took the crank with it,oh joy and not my exact words.It first sounded like the cam chain but after looking deeper i found the real pain.

so if ya can help send me a line thks
mike:

kawi6r21 · 05-14-2006

I have a couple of questions about my 01 zx6r. First off im feeling a hesitation when i give it full throttle in first the most and in 2nd also, if anyone can give me any advice or any knowledge on what that could be that would be great. Lastly i was thinking about going up 2 teeth in the rear and down 1 in the front. Im trying to pull it up but when i try to keep it up and try to throttle it in first my throttle sticks a lil, it even sticks when riding it cruising around, im sorry for such a long post but i was wondering if anyone can help me out with my problems and if i should even do the sprocket project cause ive been trying to get the stand ups good and they are really rusty since i just started to do them i dunno if the sprocket project will help. i appreciate the help if anyone can give me some advice.

04-27-2006	#221 (permalink)
ervins MOM Sept 2006 Forum Supporter Join Date: Jan 2006 Location: Castro Valley, CA Posts: 11,826	Welcome to the forum! __________________ Black 2006 ZX-10R http://cache.www.gametracker.com/ser...0/b_560x95.png

05-05-2006	#223 (permalink)
jimmyh A guy who used to ride BTK Expert Join Date: Jun 2004 Location: Chicago NW Suburbs Posts: 319	Longer mirrors for the 05-06 ZX-6R I posted this in another thread, but thought I should put it here also since this one is sticky. http://www.cooleywire.com/jimmyh/pics/mirror.html These mirrors are awesome. NO vibration. Complete view behind you. And they cost less than $60 shipped. However, they dont fold, and a little modification to the fairing bracket is required. Very simple though. __________________ Ninja Rider from the past...

05-07-2006	#226 (permalink)
r409z Sit speling cheker BTK Expert Join Date: May 2004 Location: Dolgeville, NY Posts: 429	I am excited...I just ordered the following: akrapovic slip on CA smoke integrated tail fenderkit.com eliminator no cut sliders swingarm spools tank pad gpr steering stabilizer __________________ 2006 Black ZX-6R Old Bike -- Hot Lime Green 2004 500R

05-11-2006	#234 (permalink)
onx Newbie Join Date: May 2006 Posts: 5	Sorry posted in wrong thread...thought I was posting in the 250/500cc thread (firefox tabs...got all confused =( ) Last edited by onx : 05-11-2006 at 07:57 PM.

05-12-2006	#235 (permalink)
Fortheu22 Newbie Join Date: Aug 2005 Location: Erie,PA Posts: 6	ZZR owners? I was looking at parts and I called a local dealership here and they said the 2001 zx-6r aftermarket parts MIGHT fit my 2006 kawi zzr anyone know if this is true?

05-08-2006	#228 (permalink)
1LtRocket Newbie Join Date: May 2006 Location: lexington SC Posts: 8	Help Plz!! With the FI and tech on the 06ZX-6R of mine I had to replace the servo under the seat with the block 1 muzzy sent me. Well i wasnt paying attention when i installed and got it on 180 degrees backwards when switched the key on it moved and now the FI light stays on which this was the purpose of the part. I tried to move it back but i cant. Does anyone know if i can take the servo out and reset it then put my block back on properly. the service manual on talks about dam computer error codes any feedback would be helpfull. !!!! Thanks

05-14-2006	#238 (permalink)
NinjaRdr Still On The Kickstand Join Date: Apr 2006 Location: Hampton Roads, VA Posts: 34	Hello All, Have been posting in another thread, but since my 93' zx600c is close to road readiness, thought that I would ask a question about the front wheel mounting. I removed the wheel and took it into a shop to have a new tire (120/80/16) mounted. In the process, I am putting new brake pads on it. Since I cannot remember exactly how the hub/axle spacer goes on, can you tell me if I got it on right? I installed it with the wider (lip) next to the fork. And how tight is all of this supposed to be? How freely should the wheel spin with the new brake pads, etc, installed? Thank you. NinjaRdr

05-14-2006	#239 (permalink)
otp Newbie Join Date: May 2006 Posts: 2	Heeeelllllllpppppppp! zx 600rA 1985-88 NEED CRANK SHAFT soo i can ride again.It spun the #3 piston and took the crank with it,oh joy and not my exact words.It first sounded like the cam chain but after looking deeper i found the real pain. so if ya can help send me a line thks mike:

05-14-2006	#240 (permalink)
kawi6r21 Newbie Join Date: May 2006 Location: Plant City, Florida Posts: 10	I have a couple of questions about my 01 zx6r. First off im feeling a hesitation when i give it full throttle in first the most and in 2nd also, if anyone can give me any advice or any knowledge on what that could be that would be great. Lastly i was thinking about going up 2 teeth in the rear and down 1 in the front. Im trying to pull it up but when i try to keep it up and try to throttle it in first my throttle sticks a lil, it even sticks when riding it cruising around, im sorry for such a long post but i was wondering if anyone can help me out with my problems and if i should even do the sprocket project cause ive been trying to get the stand ups good and they are really rusty since i just started to do them i dunno if the sprocket project will help. i appreciate the help if anyone can give me some advice.