Need help with LED turn signal and bullet markers.

alstensby · 06-21-2008

So I looked down while washing my bike today and notice there's a wire hanging there. Turns out, the integrated LED brake light/turn signal (left) and my left bullet marker are MIA. Looking under there, it's a bit of a mess. Doesn't help that I'm not the best when it comes to the electronics. (previous owner did this) So...anyone have this set up and can either walk me through it or show me the proper way to have it hooked up? Right now, I found a connection that gets them to blink, but all three for the left (both rear and the one in front) are blinking too fast...still at the speed indicating a light is out. But, all three light. So...something's wrong. Any help?

alstensby · 06-22-2008

A2rider · 06-22-2008

Look on the manufacturers site for tech tips. I wish I could help you, but I can't.

freightshaker · 07-05-2008

Quote:

Originally Posted by alstensby

So I looked down while washing my bike today and notice there's a wire hanging there. Turns out, the integrated LED brake light/turn signal (left) and my left bullet marker are MIA. Looking under there, it's a bit of a mess. Doesn't help that I'm not the best when it comes to the electronics. (previous owner did this) So...anyone have this set up and can either walk me through it or show me the proper way to have it hooked up? Right now, I found a connection that gets them to blink, but all three for the left (both rear and the one in front) are blinking too fast...still at the speed indicating a light is out. But, all three light. So...something's wrong. Any help?

You need an electronic flasher or a load equalizer for LED's. If you have leds in the front, then you will need a diode from Kury as well.

06-21-2008	#1 (permalink)
alstensby Big bike goes vroom vroom Forum Supporter Join Date: Dec 2007 Location: Brooklyn Park, MN Posts: 2,258	Need help with LED turn signal and bullet markers. So I looked down while washing my bike today and notice there's a wire hanging there. Turns out, the integrated LED brake light/turn signal (left) and my left bullet marker are MIA. Looking under there, it's a bit of a mess. Doesn't help that I'm not the best when it comes to the electronics. (previous owner did this) So...anyone have this set up and can either walk me through it or show me the proper way to have it hooked up? Right now, I found a connection that gets them to blink, but all three for the left (both rear and the one in front) are blinking too fast...still at the speed indicating a light is out. But, all three light. So...something's wrong. Any help? __________________ Adam L. Stensby '06 Mean Streak http://s251.photobucket.com/albums/gg315/alstensby/

06-22-2008	#2 (permalink)
alstensby Big bike goes vroom vroom Forum Supporter Join Date: Dec 2007 Location: Brooklyn Park, MN Posts: 2,258	Bump __________________ Adam L. Stensby '06 Mean Streak http://s251.photobucket.com/albums/gg315/alstensby/

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
New turn signals questions?	triple360	Kawasaki Cruisers	2	05-18-2006 09:24 PM
Front Turn Signals Replacement - Input	SleekStreak	Kawasaki Cruisers	9	03-17-2006 10:24 AM
LED Taillight/Turn Signal	Illus	Kawasaki Cruisers	5	03-11-2006 08:41 AM
Ms.Meanie's got a new tighter rear end. (LED rear light install)	trikebubble	Kawasaki Cruisers	30	10-03-2005 12:33 PM
Broken Turn signal	Trans101am	Kawasaki Cruisers	2	01-10-2005 01:31 PM

06-22-2008	#3 (permalink)
A2rider Banned BTK Expert Join Date: Mar 2006 Location: KCK Posts: 19,730	Look on the manufacturers site for tech tips. I wish I could help you, but I can't.

Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)